![LiquidInstruments-KnowledgeBase-Logo.png]](https://prm.liquidinstruments.com/hs-fs/hubfs/LiquidInstruments-KnowledgeBase-Logo.png?height=50&name=LiquidInstruments-KnowledgeBase-Logo.png){kind=logo}
Instruments
Individual instrument knowledge
Arbitrary Waveform Generator
Data Logger
Digital Filter Box
FIR Filter Builder
Frequency Response Analyzer
- Using the Frequency Response analyzer to measure inductance
- How can I plot the ratio of input 1 and input 2 using the Moku Frequency Response Analyzer?
- Can Moku:Lab analyze control loops ?
- How is the magnitude in dBm calculated in Moku:Lab’s Frequency Response Analyzer?
- Frequency Response Analyzer and harmonics
- Using the Frequency Response analyzer to measure inductance
- Frequency Response of EFI / RFI filter
Laser Lock Box
- What laser locking techniques does the Laser Lock Box support?
- Can I add an offset to the oscillator or scan output in laser lock box?
- Can I adjust the corner frequency of the low-pass filter?
- Can I set a lower corner frequency for the lowpass filter in the laser lock box?
- Does it lock continuous wave and pulsed lasers?
- What is the input to output latency for Laser Lock Box
- If Moku:Lab only has two output channels, how is it possible to generate feedback control signals as well as the modulation tone and scanning waveform?
- What if my actuator can't take negative voltages?
- Moku:Lab's Laser Lock Box : When and how should I use the slow PID controller?
- How do I generate a custom filter for laser lock box with scipy?
- How does Moku:Lab's Laser Lock Box apply gain to the input?
- Can you do fringe-side locking with Moku:Lab's Laser Lock Box?
Lock-in Amplifier
- What is the maximum rate at which I can save data, and how many points can I save?
- Can I adjust the corner frequency of the low-pass filter?
- How do I adjust the sensitivity of the Lock-In Amplifier?
- Can you do frequency domain analysis in the lock-in amplifier?
- How do I demodulate a signal at a higher harmonic with an external (PLL) reference?
- What's the difference between external and external (PLL) mode?
- The Lock-in Amplifier can readout I and Q (X and Y). What about R and theta?
- Does the Lock-in Amplifier include a PID controller for feedback applications?
- Can the Lock-in Amplifier demodulate using an external source?
- Can Moku:Lab's Lock-in Amplifier output a signal to drive a modulator?
- How does Moku:Lab's Lock-in Amplifier measure small signals with 12-bit ADCs?
- Moku:Lab Lock-in Amplifier, external trigger
Oscilloscope
- What is the difference between "Normal" and "Precision" acquisition modes?
- Can I set the channel offset in screen divisions while zooming?
- How to match channel scale settings in the Oscilloscope
- How do I adjust the sampling rate of the oscilloscope?
- What is timebase setting "roll"?
- What are the definitions of the Oscilloscope's measurements?
- What measurements can the Oscilloscope make?
- 100:1 High Voltage probe
- How to match channel scale settings in the Oscilloscope
- Moku:Lab oscilloscope probe compensation
Phasemeter
- What's the difference between Moku:Lab phasemeter and a frequency counter?
- How do I calculate the power density spectrum if the measured phase has a constant drift?
- How to change the units in the Phasemeter?
- Phasemeter output waveform resolution
- How to remove drift in Phasemeter measurement
- How are the phase and frequency precision characterized for Moku's phasemeter?
- What reference does the Phasemeter measure against?
- Can I measure the phase or frequency difference between the two input channels?
- Phasemeter output waveform resolution
PID Controller
- Can I set the PID controller by Ki, Kp, and Kd?
- How do you adjust the input gain or invert the PID input?
- What is the closed-loop bandwidth of the PID?
- What do the different colored buttons mean when configuring a PID controller?
- How do I convert Ki, Kp, Kd to crossover frequencies or vice versa?
- How can I invert my controller's response?
- How do you adjust the setpoint in PID controller?
- What is the closed-loop bandwidth of the PID?
Spectrum Analyzer
- How do I track a peak?
- Moku:Lab's spectrum analyzer 3-D timeseries
- What's the difference between the spectrum analyzer and oscilloscope FFT?
- How to improve the resolution bandwidth in spectrum analyzer?
- How do I generate waveforms on Moku:Lab’s analog outputs while running the Spectrum Analyzer?
- What's the difference between the spectrum analyzer and oscilloscope FFT?
Waveform Generator
- Can you generate a chirp with Moku:Lab's waveform generator?
- Phase synchronization of output signals across multiple Moku:Labs
- How does the 'load' affect the waveform generator?
- What is the triggered sweep mode?
- Why is the peak-to-peak voltage limited to 2 Vpp in MiM when the max output is 10 Vpp?
- Waveform generator and Amplitude Modulation
- Waveform Generator and Frequency Modulation